Kile® Clear View® Caps for Case IH*
Caps are covered by one or more of the following US & Canadian Patent numbers: #D666,227 #D689,108 #D699,772 #D700,227, #D725,688, #8,684,474 #8,833,872
#8,979,215 #9,120,514 #9,399,369 #9,458,965; #10,215,334; #10,864,953.#2,748,643, #2,794,043 and Patents Pending
K CVC STX/RT Fit STX, Steiger, Row Trac Tractors
Visualize oil levels with ease
.
K CVC CTS Fit Case Trac System Combines & Magnum Trac Tractors (Series 310, 340, 380)
Visualize oil levels with ease
.
Part K 8740-R and
Part K 8743-I
(Note the easy visibility of the inside oil levels on the photo above)
Contents of a K CVC STX/RT Kit
Contents of a K CVC CTS Kit
K 8740-PR2
This cap has a thermally-re-inforced flange which addresses flange deformity created by overheating.
K CVC 9300 kit fits-9300 Series trac Tractors
Part #K-9340-R
and Part #K-9343-I
Our Kile®Clear View® Caps fit Case IH STX/Steiger, Row trac, and MagnumTrac Tractors and
the 9300 Series Quad Trac Tractors. Also, our K CVC CTS kit for CIH trac combines-see parts page for prices. They assist you by giving operators the
ability to view and maintain proper oil levels of the idler and roller hubs. Clarity of oil, as well as sufficient oil, can help prevent the replacement and downtime of your equipment due to idler
and roller repair.
The benefits of our caps are:
- Ease of view of oil levels of idler & roller wheel hubs
- View clarity of oil
- Scratch resistant
- UV protected plastic
- High impact plastic protects against breakage
- All kits now come complete with plugs
- Resistant to weather conditions of extreme heat or cold
- View inside and outside idlers and rollers with ease
- 5 year pro-rated warranty
Contents of a K CVC 9300 Series Quad Trac Kit
Installation instructions:
STX/RT: Kit contains 16 idler & 24 roller caps, 40 plugs + o-rings for idlers & caps. See parts page for prices
For ALL Tractor Models (serial #JEE0097505 & higher):
STX®* 375, 425, 440,450, 500
Quadtrac®* 380, 430, 480, 530; 385, 435, 485, 535; 400, 450, 500, 550,600; 470, 540,580, 620
RowtracTM* 350, 400, 450, 500; 370, 420, 470, 500
* STX & Quadtrac Registered & Rowtrac trademark of CNH corporation
- Remove original Case IH cap and allow oil to completely drain.
- Remove o-ring
- Clean o-ring, housing & snap ring grove.
- Lightly oil o-ring before installing, install Kile® Clear ViewTM Cap and secure snap ring.
- Replace lubricant in hub to manufacturer's specifications.
- Install plug. Tighten with plug wrench.
Use only soap and water to clean caps, no solvents (solvents can cause clouding and premature failure of caps. Solvent use will void warranty)
CTS/OR: Kit contains 8 idler & 12 roller caps, 20 plugs + o-rings for idlers & caps. See parts page for prices.
For ALL Combine Models(example: 7010, 7120, 8010, 9120, 7230, 8230, 9230. 9240 & 9250)
For All Magnum Track Models
- Remove original Case IH cap and allow oil to completely drain.
- Remove o-ring
- Clean o-ring, housing & snap ring grove.
- Lightly oil o-ring before installing, install Kile® Clear ViewTM Cap and secure snap ring.
- Replace lubricant in hub to manufacturer's specifications.
- Install plug. Tighten with plug wrench.
Use only soap and water to clean caps, no solvents (solvents can cause clouding and premature failure of caps. Solvent use will void warranty)
Installation K CVC CTS KitCTS Kit.pdf Adobe Acrobat document [495.0 KB]
K CVC 9300 Series: Kit contains 16 idler & 24 roller caps plus hardware and instructions. See parts page for current prices
For Tractor Models: 9370, 9380 & 9390
- Remove OEM cap and allow to completely drain. To get a complete drain, the hub plug needs to be down to allow a complete drain of hub cavity.
- Clean the face of hub, removing any cork gasket that may be stuck to it.
- Install K-9343-IGE(gasket) and cap to hub.
- Secure with washers (K5161 flat washer) and bolts.
- Torque bolts around evenly, then again to 40-45 inch pounds.
- Fill cavity with manufactures recommended oil. Hub idler oil capacity is 14 ounces. Reinstall plug.
Roller:
- Remove OEM cap and allow to completely drain.
- Place part #K-237-R OR (o-ring) into o-ring groove on part #K9340-R (roller cap).
- Apply a small amount of oil to o-ring and insert into roller.
- Put washers on bolts; additional bolts are provided in the kit to allow for 6 bolt installation. (Part #K-820-HHCS)
- Torque bolts to 60-65 inch pounds.
- Fill roller cavity with OEM recommended oil. Roller oil capacity is 10 ounces.
- Install K-1215-P (plug).
- Tighten with plug wrench.
- Use only soap and water to clean caps, no solvents (solvents can cause clouding and premature failure of caps. Solvent use will void warranty)
- we ship UPS; Fed Ex; USPS (kit weight 12 lbs for STX, 5 lbs for CTS & 15 lbs for 9300)
* Case IH & it's colors are Registered trademarks of CNH Industrial